logo
Latest company case about Hydraulic Trench Cutter for Diaphragm Wall Construction in Hard Granite — Metro Station Project

Hydraulic Trench Cutter for Diaphragm Wall Construction in Hard Granite — Metro Station Project

2026-11-20

Project Overview

A specialist foundation contractor engaged in a metro station package required a reliable hard rock trenching solution for the station diaphragm wall. The station box, approximately 180 m long and 25 m wide, was designed with diaphragm walls acting as both retaining structure and permanent side walls. Geotechnical investigation showed a challenging profile: 8 to 12 m of soft to medium clay and silty sand over moderately to highly weathered granite, with fresh granite seams reaching unconfined compressive strength (UCS) values of 120 to 180 MPa in the panel toe zone. This mixed face condition — soft overburden directly above hard rock — is exactly where the hydraulic trench cutter outperforms conventional diaphragm wall grabs and milling methods.

Project data

Item Detail
Project type Metro station — diaphragm wall (retaining + permanent structure)
Location Southeast Asia, urban city center
Wall thickness 800 mm and 1,000 mm
Typical panel depth 35–45 m
Geology Clay / silty sand over weathered and fresh granite (UCS 120–180 MPa)
Verticality requirement ≤ 0.3% (1:300)
Equipment supplied APIE TC-series hydraulic trench cutter, desanding plant, guide wall system

The Challenge

The contractor initially considered crawler-mounted hydraulic grabs, but grab excavation in fresh granite proved uneconomical: chiselling and soil pumping consumed 40% of the programme, tool wear was severe, and panel verticality drifted beyond the 1:300 tolerance when breaking into inclined rock heads. Three risks dominated the method statement:

Penetrating 15–20 m of granite per panel while keeping the trench within 1:300 verticality against adjacent metro structures.

Maintaining stable slurry trench support in permeable silty sand lenses under a high groundwater table.

Achieving daily production sufficient to close the station box before the monsoon season.

A hydraulic trench cutter was selected because its twin cutting wheels mill the rock face continuously under calibrated thrust, while the built-in inclination sensors and hydraulic cylinder correction keep the panel plumb in real time — the decisive advantage of trench cutter technology for diaphragm wall construction in hard rock.

Our Solution: APIE TC-Series Hydraulic Trench Cutter

APIE supplied a TC-series hydraulic trench cutter mounted on a 150 t class crawler crane, complete with a high-capacity slurry circulation and desanding system. The cutter features two counter-rotating cutting wheels with hard-alloy tool bits, weighted cutter body for positive thrust, and fully hydraulic drive allowing precise torque and speed control between soft clay and hard granite. Key configuration data:

APIE TC-series trench cutter — key specifications

Parameter Specification
Max. excavation depth up to 120 m (project application: 45 m)
Cutting width options 600 / 800 / 1,000 / 1,200 / 1,500 mm
Cutting wheel torque 2 × 46 kNm (adjustable by rock strength)
Slurry discharge capacity approx. 320 m³/h per pump set
Verticality control Continuous sensors + hydraulic correction, achieved ≤ 0.3%
Weighted cutter body Yes — positive thrust in hard rock
Power pack Hydraulic power pack with load-sensing control

Construction Process and Site Performance

Trench cutter operation followed the primary–secondary panel sequence. Primary panels of 6.0 m were excavated in three bites; secondary panels were cut into the fresh primary panels with the cutter teeth trimming the concrete face to guarantee watertight joints. Bentonite slurry was desanded in a two-stage plant (cyclone + vibrating screen) so that sand content stayed below 4% before concrete placement. In the granite toe zone the operator reduced cutting wheel speed and increased downthrust, and the trench cutter milled fresh granite at a steady penetration rate without chisel pre-treatment.

Results

The diaphragm wall was completed two weeks ahead of the revised baseline. Measured outcomes:

Average production of 45–55 m² per shift in mixed granite — roughly 2.5 times the grab + chisel method trialled on the first panels.

Verticality of all delivered panels measured within 0.3%, verified by ultrasonic logging.

Zero trench stability incidents despite permeable sand lenses and high groundwater.

Joint quality accepted on first inspection for all secondary panels, with no water loss during dewatering of the station excavation.

The contractor has since deployed the same trench cutter on two additional rock trenching packages, confirming the machine as a versatile asset for diaphragm walls, barrette piles, and cutter soil mixing applications.

What APIE Delivered

Beyond the hydraulic trench cutter itself, APIE provided the complete deep foundation equipment package: desanding plant, slurry pumps and lines, guide wall formwork design review, cutter tool selection for the granite UCS range, commissioning, on-site operator training, and a stocked spare parts package covering cutting wheel bits, pumps, and sensor components.


Contact APIE Foundation Equipment (China) Limited

Are you planning a diaphragm wall, cut-off wall, or barrette pile project that involves hard rock, boulders, or great depth? APIE Foundation Equipment (China) Limited supplies hydraulic trench cutters, diaphragm wall grabs, desanding plants, and complete foundation engineering equipment to contractors worldwide, together with technical support, spare parts, and operator training.

Send us your geotechnical profile, panel dimensions, and schedule, and our engineering team will recommend the most suitable trench cutter configuration and a competitive quotation within 24 hours.

Email: apie@apiepiling.com

WhatsApp: +86 189 2128 7030